NeXTSTEP 3.3 (Developer) [68k, x86, SPARC, PA-RISC]

home *** CD-ROM | disk | FTP | other *** search

/ NeXTSTEP 3.3 (Developer)…68k, x86, SPARC, PA-RISC] / NeXTSTEP 3.3 Dev Intel.iso / NextDeveloper / Source / GNU / emacs / info / termcap-2 (.txt) < prev next >

Wrap

GNU Info File | 1992-10-30 | 44KB | 721 lines

This is Info file ../info/termcap, produced by Makeinfo-1.49 from the input file termcap.texi. This file documents the termcap library of the GNU system. Copyright (C) 1988 Free Software Foundation, Inc. Permission is granted to make and distribute verbatim copies of this manual provided the copyright notice and this permission notice are preserved on all copies. Permission is granted to copy and distribute modified versions of this manual under the conditions for verbatim copying, provided that the entire resulting derived work is distributed under the terms of a permission notice identical to this one. Permission is granted to copy and distribute translations of this manual into another language, under the above conditions for modified versions, except that this permission notice may be stated in a translation approved by the Foundation. File: termcap, Node: Capabilities, Next: Summary, Prev: Data Base, Up: Top Definitions of the Terminal Capabilities **************************************** This section is divided into many subsections, each for one aspect of use of display terminals. For writing a display program, you usually need only check the subsections for the operations you want to use. For writing a terminal description, you must read each subsection and fill in the capabilities described there. String capabilities that are display commands may require numeric parameters (*note Parameters::.). Most such capabilities do not use parameters. When a capability requires parameters, this is explicitly stated at the beginning of its definition. In simple cases, the first or second sentence of the definition mentions all the parameters, in the order they should be given, using a name in upper case for each one. For example, the `rp' capability is a command that requires two parameters; its definition begins as follows: String of commands to output a graphic character C, repeated N times. In complex cases or when there are many parameters, they are described explicitly. When a capability is described as obsolete, this means that programs should not be written to look for it, but terminal descriptions should still be written to provide it. When a capability is described as very obsolete, this means that it should be omitted from terminal descriptions as well. * Menu: * Basic:: Basic characteristics. * Screen Size:: Screen size, and what happens when it changes. * Cursor Motion:: Various ways to move the cursor. * Scrolling:: Pushing text up and down on the screen. * Wrapping:: What happens if you write a character in the last column. * Windows:: Limiting the part of the window that output affects. * Clearing:: Erasing one or many lines. * Insdel Line:: Making new blank lines in mid-screen; deleting lines. * Insdel Char:: Inserting and deleting characters within a line. * Standout:: Highlighting some of the text. * Underlining:: Underlining some of the text. * Cursor Visibility:: Making the cursor more or less easy to spot. * Bell:: Attracts user's attention; not localized on the screen. * Keypad:: Recognizing when function keys or arrows are typed. * Meta Key:: META acts like an extra shift key. * Initialization:: Commands used to initialize or reset the terminal. * Pad Specs:: Info for the kernel on how much padding is needed. * Status Line:: A status line displays "background" information. * Half-Line:: Moving by half-lines, for superscripts and subscripts. * Printer:: Controlling auxiliary printers of display terminals. File: termcap, Node: Basic, Next: Screen Size, Prev: Capabilities, Up: Capabilities Basic Characteristics ===================== This section documents the capabilities that describe the basic and nature of the terminal, and also those that are relevant to the output of graphic characters. Flag whose presence means that the terminal can overstrike. This means that outputting a graphic character does not erase whatever was present in the same character position before. The terminals that can overstrike include printing terminals, storage tubes (all obsolete nowadays), and many bit-map displays. Flag whose presence means that outputting a space erases a character position even if the terminal supports overstriking. If this flag is not present and overstriking is supported, output of a space has no effect except to move the cursor. (On terminals that do not support overstriking, you can always assume that outputting a space at a position erases whatever character was previously displayed there.) Flag whose presence means that this terminal type is a generic type which does not really describe any particular terminal. Generic types are intended for use as the default type assigned when the user connects to the system, with the intention that the user should specify what type he really has. One example of a generic type is the type `network'. Since the generic type cannot say how to do anything interesting with the terminal, termcap-using programs will always find that the terminal is too weak to be supported if the user has failed to specify a real terminal type in place of the generic one. The `gn' flag directs these programs to use a different error message: "You have not specified your real terminal type", rather than "Your terminal is not powerful enough to be used". Flag whose presence means this is a hardcopy terminal. String of commands to output a graphic character C, repeated N times. The first parameter value is the ASCII code for the desired character, and the second parameter is the number of times to repeat the character. Often this command requires padding proportional to the number of times the character is repeated. This effect can be had by using parameter arithmetic with `%'-sequences to compute the amount of padding, then generating the result as a number at the front of the string so that `tputs' will treat it as padding. Flag whose presence means that the ASCII character `~' cannot be output on this terminal because it is used for display commands. Programs handle this flag by checking all text to be output and replacing each `~' with some other character(s). If this is not done, the screen will be thoroughly garbled. The old Hazeltine terminals that required such treatment are probably very rare today, so you might as well not bother to support this flag. String whose presence means the terminal has a settable command character. The value of the string is the default command character (which is usually ESC). All the strings of commands in the terminal description should be written to use the default command character. If you are writing an application program that changes the command character, use the `CC' capability to figure out how to translate all the display commands to work with the new command character. Most programs have no reason to look at the `CC' capability. Flag whose presence identifies Superbee terminals which are unable to transmit the characters ESC and `Control-C'. Programs which support this flag are supposed to check the input for the code sequences sent by the F1 and F2 keys, and pretend that ESC or `Control-C' (respectively) had been read. But this flag is obsolete, and not worth supporting. File: termcap, Node: Screen Size, Next: Cursor Motion, Prev: Basic, Up: Capabilities Screen Size =========== A terminal description has two capabilities, `co' and `li', that describe the screen size in columns and lines. But there is more to the question of screen size than this. On some operating systems the "screen" is really a window and the effective width can vary. On some of these systems, `tgetnum' uses the actual width of the window to decide what value to return for the `co' capability, overriding what is actually written in the terminal description. On other systems, it is up to the application program to check the actual window width using a system call. For example, on BSD 4.3 systems, the system call `ioctl' with code `TIOCGWINSZ' will tell you the current screen size. On all window systems, termcap is powerless to advise the application program if the user resizes the window. Application programs must deal with this possibility in a system-dependent fashion. On some systems the C shell handles part of the problem by detecting changes in window size and setting the `TERMCAP' environment variable appropriately. This takes care of application programs that are started subsequently. It does not help application programs already running. On some systems, including BSD 4.3, all programs using a terminal get a signal named `SIGWINCH' whenever the screen size changes. Programs that use termcap should handle this signal by using `ioctl TIOCGWINSZ' to learn the new screen size. Numeric value, the width of the screen in character positions. Even hardcopy terminals normally have a `co' capability. Numeric value, the height of the screen in lines. File: termcap, Node: Cursor Motion, Next: Wrapping, Prev: Screen Size, Up: Capabilities Cursor Motion ============= Termcap assumes that the terminal has a "cursor", a spot on the screen where a visible mark is displayed, and that most display commands take effect at the position of the cursor. It follows that moving the cursor to a specified location is very important. There are many terminal capabilities for different cursor motion operations. A terminal description should define as many as possible, but most programs do not need to use most of them. One capability, `cm', moves the cursor to an arbitrary place on the screen; this by itself is sufficient for any application as long as there is no need to support hardcopy terminals or certain old, weak displays that have only relative motion commands. Use of other cursor motion capabilities is an optimization, enabling the program to output fewer characters in some common cases. If you plan to use the relative cursor motion commands in an application program, you must know what the starting cursor position is. To do this, you must keep track of the cursor position and update the records each time anything is output to the terminal, including graphic characters. In addition, it is necessary to know whether the terminal wraps after writing in the rightmost column. *Note Wrapping::. One other motion capability needs special mention: `nw' moves the cursor to the beginning of the following line, perhaps clearing all the starting line after the cursor, or perhaps not clearing at all. This capability is a least common denominator that is probably supported even by terminals that cannot do most other things such as `cm' or `do'. Even hardcopy terminals can support `nw'. String of commands to position the cursor at line L, column C. Both parameters are origin-zero, and are defined relative to the screen, not relative to display memory. All display terminals except a few very obsolete ones support `cm', so it is acceptable for an application program to refuse to operate on terminals lacking `cm'. String of commands to move the cursor to the upper left corner of the screen (this position is called the "home position"). In terminals where the upper left corner of the screen is not the same as the beginning of display memory, this command must go to the upper left corner of the screen, not the beginning of display memory. Every display terminal supports this capability, and many application programs refuse to operate if the `ho' capability is missing. String of commands to move the cursor to the lower left corner of the screen. On some terminals, moving up from home position does this, but programs should never assume that will work. Just output the `ll' string (if it is provided); if moving to home position and then moving up is the best way to get there, the `ll' command will do that. String of commands to move the cursor to the beginning of the line it is on. If this capability is not specified, many programs assume they can use the ASCII carriage return character for this. String of commands to move the cursor left one column. Unless the `bw' flag capability is specified, the effect is undefined if the cursor is at the left margin; do not use this command there. If `bw' is present, this command may be used at the left margin, and it wraps the cursor to the last column of the preceding line. String of commands to move the cursor right one column. The effect is undefined if the cursor is at the right margin; do not use this command there, not even if `am' is present. String of commands to move the cursor vertically up one line. The effect of sending this string when on the top line is undefined; programs should never use it that way. String of commands to move the cursor vertically down one line. The effect of sending this string when on the bottom line is undefined; programs should never use it that way. The original idea was that this string would not contain a newline character and therefore could be used without disabling the kernel's usual habit of converting of newline into a carriage-return newline sequence. But many terminal descriptions do use newline in the `do' string, so this is not possible; a program which sends the `do' string must disable output conversion in the kernel (*note Initialize::.). Flag whose presence says that `le' may be used in column zero to move to the last column of the preceding line. If this flag is not present, `le' should not be used in column zero. String of commands to move the cursor to start of next line, possibly clearing rest of line (following the cursor) before moving. `DO', `UP', `LE', `RI' Strings of commands to move the cursor N lines down vertically, up vertically, or N columns left or right. Do not attempt to move past any edge of the screen with these commands; the effect of trying that is undefined. Only a few terminal descriptions provide these commands, and most programs do not use them. String of commands to position the cursor at line L, column C, relative to display memory. Both parameters are origin-zero. This capability is present only in terminals where there is a difference between screen-relative and memory-relative addressing, and not even in all such terminals. String of commands to position the cursor at column C in the same line it is on. This is a special case of `cm' in which the vertical position is not changed. The `ch' capability is provided only when it is faster to output than `cm' would be in this special case. Programs should not assume most display terminals have `ch'. String of commands to position the cursor at line L in the same column. This is a special case of `cm' in which the horizontal position is not changed. The `cv' capability is provided only when it is faster to output than `cm' would be in this special case. Programs should not assume most display terminals have `cv'. String of commands to make the terminal save the current cursor position. Only the last saved position can be used. If this capability is present, `rc' should be provided also. Most terminals have neither. String of commands to make the terminal restore the last saved cursor position. If this capability is present, `sc' should be provided also. Most terminals have neither. String of commands to advance to the next page, for a hardcopy terminal. String of commands to move the cursor right to the next hardware tab stop column. Missing if the terminal does not have any kind of hardware tabs. Do not send this command if the kernel's terminal modes say that the kernel is expanding tabs into spaces. String of commands to move the cursor left to the previous hardware tab stop column. Missing if the terminal has no such ability; many terminals do not. Do not send this command if the kernel's terminal modes say that the kernel is expanding tabs into spaces. The following obsolete capabilities should be included in terminal descriptions when appropriate, but should not be looked at by new programs. Flag whose presence means the terminal does not support the ASCII carriage return character as `cr'. This flag is needed because old programs assume, when the `cr' capability is missing, that ASCII carriage return can be used for the purpose. We use `nc' to tell the old programs that carriage return may not be used. New programs should not assume any default for `cr', so they need not look at `nc'. However, descriptions should contain `nc' whenever they do not contain `cr'. Flag whose presence means that the ASCII tab character may not be used for cursor motion. This flag exists because old programs assume, when the `ta' capability is missing, that ASCII tab can be used for the purpose. We use `xt' to tell the old programs not to use tab. New programs should not assume any default for `ta', so they need not look at `xt' in connection with cursor motion. Note that `xt' also has implications for standout mode (*note Standout::.). It is obsolete in regard to cursor motion but not in regard to standout. In fact, `xt' means that the terminal is a Teleray 1061. Very obsolete alternative name for the `le' capability. Flag whose presence means that the ASCII character backspace may be used to move the cursor left. Obsolete; look at `le' instead. Obsolete capability which is a string that can either be used to move the cursor down or to scroll. The same string must scroll when used on the bottom line and move the cursor when used on any other line. New programs should use `do' or `sf', and ignore `nl'. If there is no `nl' capability, some old programs assume they can use the newline character for this purpose. These programs follow a bad practice, but because they exist, it is still desirable to define the `nl' capability in a terminal description if the best way to move down is *not* a newline. File: termcap, Node: Wrapping, Next: Scrolling, Prev: Cursor Motion, Up: Capabilities Wrapping ======== "Wrapping" means moving the cursor from the right margin to the left margin of the following line. Some terminals wrap automatically when a graphic character is output in the last column, while others do not. Most application programs that use termcap need to know whether the terminal wraps. There are two special flag capabilities to describe what the terminal does when a graphic character is output in the last column. Flag whose presence means that writing a character in the last column causes the cursor to wrap to the beginning of the next line. If `am' is not present, writing in the last column leaves the cursor at the place where the character was written. Writing in the last column of the last line should be avoided on terminals with `am', as it may or may not cause scrolling to occur (*note Scrolling::.). Scrolling is surely not what you would intend. If your program needs to check the `am' flag, then it also needs to check the `xn' flag which indicates that wrapping happens in a strange way. Many common terminals have the `xn' flag. Flag whose presence means that the cursor wraps in a strange way. At least two distinct kinds of strange behavior are known; the termcap data base does not contain anything to distinguish the two. On Concept-100 terminals, output in the last column wraps the cursor almost like an ordinary `am' terminal. But if the next thing output is a newline, it is ignored. DEC VT-100 terminals (when the wrap switch is on) do a different strange thing: the cursor wraps only if the next thing output is another graphic character. In fact, the wrap occurs when the following graphic character is received by the terminal, before the character is placed on the screen. On both of these terminals, after writing in the last column a following graphic character will be displayed in the first column of the following line. But the effect of relative cursor motion characters such as newline or backspace at such a time depends on the terminal. The effect of erase or scrolling commands also depends on the terminal. You can't assume anything about what they will do on a terminal that has `xn'. So, to be safe, you should never do these things at such a time on such a terminal. To be sure of reliable results on a terminal which has the `xn' flag, output a `cm' absolute positioning command after writing in the last column. Another safe thing to do is to output carriage-return newline, which will leave the cursor at the beginning of the following line. File: termcap, Node: Scrolling, Next: Windows, Prev: Wrapping, Up: Capabilities Scrolling ========= "Scrolling" means moving the contents of the screen up or down one or more lines. Moving the contents up is "forward scrolling"; moving them down is "reverse scrolling". Scrolling happens after each line of output during ordinary output on most display terminals. But in an application program that uses termcap for random-access output, scrolling happens only when explicitly requested with the commands in this section. Some terminals have a "scroll region" feature. This lets you limit the effect of scrolling to a specified range of lines. Lines outside the range are unaffected when scrolling happens. The scroll region feature is available if either `cs' or `cS' is present. String of commands to scroll the screen one line up, assuming it is output with the cursor at the beginning of the bottom line. String of commands to scroll the screen one line down, assuming it is output with the cursor at the beginning of the top line. String of commands to scroll the screen N lines up, assuming it is output with the cursor at the beginning of the bottom line. String of commands to scroll the screen N line down, assuming it is output with the cursor at the beginning of the top line. String of commands to set the scroll region. This command takes two parameters, START and END, which are the line numbers (origin-zero) of the first line to include in the scroll region and of the last line to include in it. When a scroll region is set, scrolling is limited to the specified range of lines; lines outside the range are not affected by scroll commands. Do not try to move the cursor outside the scroll region. The region remains set until explicitly removed. To remove the scroll region, use another `cs' command specifying the full height of the screen. The cursor position is undefined after the `cs' command is set, so position the cursor with `cm' immediately afterward. String of commands to set the scroll region using parameters in different form. The effect is the same as if `cs' were used. Four parameters are required: 1. Total number of lines on the screen. 2. Number of lines above desired scroll region. 3. Number of lines below (outside of) desired scroll region. 4. Total number of lines on the screen, the same as the first parameter. This capability is a GNU extension that was invented to allow the Ann Arbor Ambassador's scroll-region command to be described; it could also be done by putting non-Unix `%'-sequences into a `cs' string, but that would have confused Unix programs that used the `cs' capability with the Unix termcap. Currently only GNU Emacs uses the `cS' capability. Flag which means that the terminal does not normally scroll for ordinary sequential output. For modern terminals, this means that outputting a newline in ordinary sequential output with the cursor on the bottom line wraps to the top line. For some obsolete terminals, other things may happen. The terminal may be able to scroll even if it does not normally do so. If the `sf' capability is provided, it can be used for scrolling regardless of `ns'. Flag whose presence means that lines scrolled up off the top of the screen may come back if scrolling down is done subsequently. The `da' and `db' flags do not, strictly speaking, affect how to scroll. But programs that scroll usually need to clear the lines scrolled onto the screen, if these flags are present. Flag whose presence means that lines scrolled down off the bottom of the screen may come back if scrolling up is done subsequently. Numeric value, the number of lines of display memory that the terminal has. A value of zero means that the terminal has more display memory than can fit on the screen, but no fixed number of lines. (The number of lines may depend on the amount of text in each line.) Any terminal description that defines `SF' should also define `sf'; likewise for `SR' and `sr'. However, many terminals can only scroll by one line at a time, so it is common to find `sf' and not `SF', or `sr' without `SR'. Therefore, all programs that use the scrolling facilities should be prepared to work with `sf' in the case that `SF' is absent, and likewise with `sr'. On the other hand, an application program that uses only `sf' and not `SF' is acceptable, though slow on some terminals. When outputting a scroll command with `tputs', the NLINES argument should be the total number of lines in the portion of the screen being scrolled. Very often these commands require padding proportional to this number of lines. *Note Padding::. File: termcap, Node: Windows, Next: Clearing, Prev: Scrolling, Up: Capabilities Windows ======= A "window", in termcap, is a rectangular portion of the screen to which all display operations are restricted. Wrapping, clearing, scrolling, insertion and deletion all operate as if the specified window were all the screen there was. String of commands to set the terminal output screen window. This string requires four parameters, all origin-zero: 1. The first line to include in the window. 2. The last line to include in the window. 3. The first column to include in the window. 4. The last column to include in the window. Most terminals do not support windows. File: termcap, Node: Clearing, Next: Insdel Line, Prev: Windows, Up: Capabilities Clearing Parts of the Screen ============================ There are several terminal capabilities for clearing parts of the screen to blank. All display terminals support the `cl' string, and most display terminals support all of these capabilities. String of commands to clear the entire screen and position the cursor at the upper left corner. String of commands to clear the line the cursor is on, and all the lines below it, down to the bottom of the screen. This command string should be used only with the cursor in column zero; their effect is undefined if the cursor is elsewhere. String of commands to clear from the cursor to the end of the current line. String of commands to clear N characters, starting with the character that the cursor is on. This command string is expected to leave the cursor position unchanged. The parameter N should never be large enough to reach past the right margin; the effect of such a large parameter would be undefined. Clear to end of line (`ce') is extremely important in programs that maintain an updating display. Nearly all display terminals support this operation, so it is acceptable for a an application program to refuse to work if `ce' is not present. However, if you do not want this limitation, you can accomplish clearing to end of line by outputting spaces until you reach the right margin. In order to do this, you must know the current horizontal position. Also, this technique assumes that writing a space will erase. But this happens to be true on all the display terminals that fail to support `ce'. File: termcap, Node: Insdel Line, Next: Insdel Char, Prev: Clearing, Up: Capabilities Insert/Delete Line ================== "Inserting a line" means creating a blank line in the middle of the screen, and pushing the existing lines of text apart. In fact, the lines above the insertion point do not change, while the lines below move down, and one is normally lost at the bottom of the screen. "Deleting a line" means causing the line to disappear from the screen, closing up the gap by moving the lines below it upward. A new line appears at the bottom of the screen. Usually this line is blank, but on terminals with the `db' flag it may be a line previously moved off the screen bottom by scrolling or line insertion. Insertion and deletion of lines is useful in programs that maintain an updating display some parts of which may get longer or shorter. They are also useful in editors for scrolling parts of the screen, and for redisplaying after lines of text are killed or inserted. Many terminals provide commands to insert or delete a single line at the cursor position. Some provide the ability to insert or delete several lines with one command, using the number of lines to insert or delete as a parameter. Always move the cursor to column zero before using any of these commands. String of commands to insert a blank line before the line the cursor is on. The existing line, and all lines below it, are moved down. The last line in the screen (or in the scroll region, if one is set) disappears and in most circumstances is discarded. It may not be discarded if the `db' is present (*note Scrolling::.). The cursor must be at the left margin before this command is used. This command does not move the cursor. String of commands to delete the line the cursor is on. The following lines move up, and a blank line appears at the bottom of the screen (or bottom of the scroll region). If the terminal has the `db' flag, a nonblank line previously pushed off the screen bottom may reappear at the bottom. The cursor must be at the left margin before this command is used. This command does not move the cursor. String of commands to insert N blank lines before the line that the cursor is on. It is like `al' repeated N times, except that it is as fast as one `al'. String of commands to delete N lines starting with the line that the cursor is on. It is like `dl' repeated N times, except that it is as fast as one `dl'. Any terminal description that defines `AL' should also define `al'; likewise for `DL' and `dl'. However, many terminals can only insert or delete one line at a time, so it is common to find `al' and not `AL', or `dl' without `DL'. Therefore, all programs that use the insert and delete facilities should be prepared to work with `al' in the case that `AL' is absent, and likewise with `dl'. On the other hand, it is acceptable to write an application that uses only `al' and `dl' and does not look for `AL' or `DL' at all. If a terminal does not support line insertion and deletion directly, but does support a scroll region, the effect of insertion and deletion can be obtained with scrolling. However, it is up to the individual user program to check for this possibility and use the scrolling commands to get the desired result. It is fairly important to implement this alternate strategy, since it is the only way to get the effect of line insertion and deletion on the popular VT100 terminal. Insertion and deletion of lines is affected by the scroll region on terminals that have a settable scroll region. This is useful when it is desirable to move any few consecutive lines up or down by a few lines. *Note Scrolling::. The line pushed off the bottom of the screen is not lost if the terminal has the `db' flag capability; instead, it is pushed into display memory that does not appear on the screen. This is the same thing that happens when scrolling pushes a line off the bottom of the screen. Either reverse scrolling or deletion of a line can bring the apparently lost line back onto the bottom of the screen. If the terminal has the scroll region feature as well as `db', the pushed-out line really is lost if a scroll region is in effect. When outputting an insert or delete command with `tputs', the NLINES argument should be the total number of lines from the cursor to the bottom of the screen (or scroll region). Very often these commands require padding proportional to this number of lines. *Note Padding::. For `AL' and `DL' the NLINES argument should *not* depend on the number of lines inserted or deleted; only the total number of lines affected. This is because it is just as fast to insert two or N lines with `AL' as to insert one line with `al'. File: termcap, Node: Insdel Char, Next: Standout, Prev: Insdel Line, Up: Capabilities Insert/Delete Character ======================= "Inserting a character" means creating a blank space in the middle of a line, and pushing the rest of the line rightward. The character in the rightmost column is lost. "Deleting a character" means causing the character to disappear from the screen, closing up the gap by moving the rest of the line leftward. A blank space appears in the rightmost column. Insertion and deletion of characters is useful in programs that maintain an updating display some parts of which may get longer or shorter. It is also useful in editors for redisplaying the results of editing within a line. Many terminals provide commands to insert or delete a single character at the cursor position. Some provide the ability to insert or delete several characters with one command, using the number of characters to insert or delete as a parameter. Many terminals provide an insert mode in which outputting a graphic character has the added effect of inserting a position for that character. A special command string is used to enter insert mode and another is used to exit it. The reason for designing a terminal with an insert mode rather than an insert command is that inserting character positions is usually followed by writing characters into them. With insert mode, this is as fast as simply writing the characters, except for the fixed overhead of entering and leaving insert mode. However, when the line speed is great enough, padding may be required for the graphic characters output in insert mode. Some terminals require you to enter insert mode and then output a special command for each position to be inserted. Or they may require special commands to be output before or after each graphic character to be inserted. Deletion of characters is usually accomplished by a straightforward command to delete one or several positions; but on some terminals, it is necessary to enter a special delete mode before using the delete command, and leave delete mode afterward. Sometimes delete mode and insert mode are the same mode. Some terminals make a distinction between character positions in which a space character has been output and positions which have been cleared. On these terminals, the effect of insert or delete character runs to the first cleared position rather than to the end of the line. In fact, the effect may run to more than one line if there is no cleared position to stop the shift on the first line. These terminals are identified by the `in' flag capability. On terminals with the `in' flag, the technique of skipping over characters that you know were cleared, and then outputting text later on in the same line, causes later insert and delete character operations on that line to do nonstandard things. A program that has any chance of doing this must check for the `in' flag and must be careful to write explicit space characters into the intermediate columns when `in' is present. A plethora of terminal capabilities are needed to describe all of this complexity. Here is a list of them all. Following the list, we present an algorithm for programs to use to take proper account of all of these capabilities. String of commands to enter insert mode. If the terminal has no special insert mode, but it can insert characters with a special command, `im' should be defined with a null value, because the `vi' editor assumes that insertion of a character is impossible if `im' is not provided. New programs should not act like `vi'. They should pay attention to `im' only if it is defined. String of commands to leave insert mode. This capability must be present if `im' is. On a few old terminals the same string is used to enter and exit insert mode. This string turns insert mode on if it was off, and off it it was on. You can tell these terminals because the `ei' string equals the `im' string. If you want to support these terminals, you must always remember accurately whether insert mode is in effect. However, these terminals are obsolete, and it is reasonable to refuse to support them. On all modern terminals, you can safely output `ei' at any time to ensure that insert mode is turned off. String of commands to insert one character position at the cursor. The cursor does not move. If outputting a graphic character while in insert mode is sufficient to insert the character, then the `ic' capability should be defined with a null value. If your terminal offers a choice of ways to insert--either use insert mode or use a special command--then define `im' and do not define `ic', since this gives the most efficient operation when several characters are to be inserted. *Do not* define both strings, for that means that *both* must be used each time insertion is done. String of commands to output following an inserted graphic character in insert mode. Often it is used just for a padding spec, when padding is needed after an inserted character (*note Padding::.). String of commands to insert N character positions at and after the cursor. It has the same effect as repeating the `ic' string and a space, N times. If `IC' is provided, application programs may use it without first entering insert mode. Flag whose presence means it is safe to move the cursor while in insert mode and assume the terminal remains in insert mode. Flag whose presence means that the terminal distinguishes between character positions in which space characters have been output and positions which have been cleared. An application program can assume that the terminal can do character insertion if *any one of* the capabilities `IC', `im', `ic' or `ip' is provided. To insert N blank character positions, move the cursor to the place to insert them and follow this algorithm: 1. If an `IC' string is provided, output it with parameter N and you are finished. Otherwise (or if you don't want to bother to look for an `IC' string) follow the remaining steps. 2. Output the `im' string, if there is one, unless the terminal is already in insert mode. 3. Repeat steps 4 through 6, N times. 4. Output the `ic' string if any. 5. Output a space. 6. Output the `ip' string if any. 7. Output the `ei' string, eventually, to exit insert mode. There is no need to do this right away. If the `mi' flag is present, you can move the cursor and the cursor will remain in insert mode; then you can do more insertion elsewhere without reentering insert mode. To insert N graphic characters, position the cursor and follow this algorithm: 1. If an `IC' string is provided, output it with parameter N, then output the graphic characters, and you are finished. Otherwise (or if you don't want to bother to look for an `IC' string) follow the remaining steps. 2. Output the `im' string, if there is one, unless the terminal is already in insert mode. 3. For each character to be output, repeat steps 4 through 6. 4. Output the `ic' string if any. 5. Output the next graphic character. 6. Output the `ip' string if any. 7. Output the `ei' string, eventually, to exit insert mode. There is no need to do this right away. If the `mi' flag is present, you can move the cursor and the cursor will remain in insert mode; then you can do more insertion elsewhere without reentering insert mode. Note that this is not the same as the original Unix termcap specifications in one respect: it assumes that the `IC' string can be used without entering insert mode. This is true as far as I know, and it allows you be able to avoid entering and leaving insert mode, and also to be able to avoid the inserted-character padding after the characters that go into the inserted positions. Deletion of characters is less complicated; deleting one column is done by outputting the `dc' string. However, there may be a delete mode that must be entered with `dm' in order to make `dc' work. String of commands to delete one character position at the cursor. If `dc' is not present, the terminal cannot delete characters. String of commands to delete N characters starting at the cursor. It has the same effect as repeating the `dc' string N times. Any terminal description that has `DC' also has `dc'. String of commands to enter delete mode. If not present, there is no delete mode, and `dc' can be used at any time (assuming there is a `dc'). String of commands to exit delete mode. This must be present if `dm' is. To delete N character positions, position the cursor and follow these steps: 1. If the `DC' string is present, output it with parameter N and you are finished. Otherwise, follow the remaining steps. 2. Output the `dm' string, unless you know the terminal is already in delete mode. 3. Output the `dc' string N times. 4. Output the `ed' string eventually. If the flag capability `mi' is present, you can move the cursor and do more deletion without leaving and reentering delete mode. As with the `IC' string, we have departed from the original termcap specifications by assuming that `DC' works without entering delete mode even though `dc' would not. If the `dm' and `im' capabilities are both present and have the same value, it means that the terminal has one mode for both insertion and deletion. It is useful for a program to know this, because then it can do insertions after deletions, or vice versa, without leaving insert/delete mode and reentering it.